- Flows up to 2.2 L/s
- Pressure differential backwash control
- Control panel with indication lights
- Low consumption for backwash
- Screen sizes available as detailed below
- 304 Grade stainless steel housing
- Min operating presssure: 200kPa
- Max operating pressure: 500kPa
- 25mm (1”) BSPM Inlet/Outlet
- 32mm (1 1/4”) BSPM Inlet/Outlet
-
-
- Compact modular design, can be connected in stacks.
- Minimal pipework due to innovative manifold meaning less maintenance, and smaller footprint.
- Pump incorporates energy recovery from high pressure brine flow which provides over 60% of the drive energy providing very kWh/m3 of desalinated water.
- Axial-piston high pressure pump constructed of corrosion resistant Duplex and Super Duplex steel. Non metallic parts are manufactured from corrosion and wear resistant PEEK Polymer.
- Contacting surfaces lubricated by sea water flowing through them.
-
- Flows up to 12.5 L/s
- Pressure differential backwash control
- Control panel with indication lights and volt free contacts
- Low consumption for backwash
- Screen sizes available as detailed below
- 304 Grade stainless steel housing (316L available)
- Min operating presssure: 200kPa
- Max operating pressure: 1,000kPa
- 50mm BSP, 80mm BSP, DN80 flange inlet/outlet
- Backwash counter to monitor number of cleaning cycles performed
-
- Flows up to 33.0 L/s
- Pressure differential backwash control
- Control panel with indication lights and volt free contacts
- Low consumption for backwash
- Screen sizes available as detailed below
- 304 Grade stainless steel housing (316L available)
- Min operating presssure: 200kPa
- Max operating pressure: 1,000kPa
- 80mm (3”) BPSM & DN100/DN150 Flange Inlet/Outlet
- Backwash counter to monitor number of cleaning cycles performed
-
- Flows up to 86.0 L/s
- Pressure differential backwash control
- Control panel with indication lights and volt free contacts
- Low consumption for backwash
- Screen sizes available as detailed below
- 304 Grade stainless steel housing (316L available)
- Min operating presssure: 200kPa
- Max operating pressure: 1,000kPa
- DN100, DN150, DN200, DN250 Flange Inlet/Outlet
- Backwash counter to monitor number of cleaning cycles performed
-
- Flows up to 3.0 L/s (180 L/m)
- Moulded twin head system ensures compact installation and no leaks
- Dual stage filtration for longer filter life
- Durable reinforced polypropylene filter housings
- Wall-mount brackets with all kits
- Max operating pressure: 830kPa
-
- Flows up to 1.0 L/s (60 L/m)
- Moulded twin head system ensures compact installation and no leaks
- Dual stage filtration for longer filter life
- Durable reinforced polypropylene filter housings
- Supplied with mounting screws and spanner, and wall-mount bracket
- Utilises high output eco-friendly UV disinfection technology to ensure maximum bacteria kill
- Max operating pressure: 830kPa
- Includes 316 S/S flexi connector and fittings to join filter housings to UV system
-
- Flows up to 60L/m (5.4m3/h)
- Moulded twin head system ensures compact installation and no leaks
- Dual stage filtration for longer filter life
- Durable reinforced polypropylene filter housings
- Supplied with mounting screws and spanner
- Wall-mount bracket supplied separate
- Utilises high output eco-friendly UV disinfection technology to ensure maximum bacteria kill
- Max operating pressure: 830kPa
- Includes 316 S/S flexi connector and fittings to join filter housings to UV system
-
- Flows up to 3.0 L/s (180 L/m)
- Moulded twin head system ensures
- Dual stage filtration for longer filter life
- Durable reinforced polypropylene filter housings
- Supplied with mounting screws and spanner. Wall-mount bracket supplied separate
- Utilises high output eco-friendly UV disinfection technology to ensure maximum bacteria kill
- Max operating pressure: 830kPa
- Includes 316 S/S flexi connector and fittings to join filter housings to UV system
-
- Flows up to 60L/m (5.4m3/h)
- Moulded twin head system ensures compact installation and no leaks
- Dual stage filtration for longer filter life
- Durable reinforced polypropylene filter housings
- Supplied with mounting screws and spanner. Wall-mount bracket supplied separate
- Utilises high output eco-friendly UV disinfection technology to ensure maximum bacteria kill
- Max operating pressure: 830kPa
- Includes 316 S/S flexi connector and fittings to join filter housings to UV system
-
- Complete purified water system incorporating RO, tank and distribution
- Ideal for single/multiple Automatic Endoscope Reprocessors (AERs) feed
- Thermal disinfection at >80°C carried out automatically out of hours
- Water recirculates at user specified temperature via the UV and 0.04 micron endotoxin retention flter to all point(s) of use
- Compact and easy to install with footprints as small as550mm wide x 600mm deep (1980mm H)
-
- Complete purified water system incorporating RO, tank and distribution pumps
- Ideal for single/multiple Automatic Endoscope Reprocessors (AERs) feed, Washer-disinfectors and sterilisers
- Duplex RO units in a single SS304 skid, with wheels for maximum resilience
- Thermal disinfection at >80°C carried out automatically out of hours
- Water recirculates at user specified temperature via the UV and 0.04 micron endotoxin retention filter to all point(s) of use
- Compact and easy to install with footprints as small as 1400mm wide x 710mm deep (1950mm H)
- Quiet operation means suitable for positioning in washroom next to AER’s and in the CSSD if required (system can be supplied with panels for CSSD installation)
-
- Ideal for facilities with > 8 operating theatres
- Duplex RO systems on the same skid for maximum resilience
- Option of electrical or steam heating
- Prefabricated, skid-mounted modular system means quick installation and less downtime
- Thermal disinfection to >80°C automatically out of hours
- Water recirculates at elevated temperatures to all points of use (user adjustable)
- Designed to comply with HTM 01-06 and AS/NZS 4187 requirements
- Flexible, modular design concept offers 48 combination
-
- Specially designed and tested Sterilume™-EX lamps provide consistent and reliable ultraviolet output over the entire life of the lamp to ensure continuous purification
- Built with a durable stainless steel chamber to prolong life and eliminate ultraviolet light degradation
- The controller visually displays the remaining lamp life and will go into alarm if the lamp fails
- The controller has a sealed case to prevent damage from accidental water intrusion and is fully CSA and CE compliant
- Max operating pressure: 860kPa
-
- High intensity lamps provide consistent and reliable ultraviolet output over the entire life of the lamp
- Built with a durable stainless steel chamber to prolong life and eliminate ultraviolet light degradation
- Audible and visual lamp fail alarm
- Max operating pressure: 860kPa
- Volt free contacts for lamp fail alarm
- Higher pressure versions available (eg 1000kPa, 1600kPa)
-
- Specially designed and tested Sterilume™-EX lamps provide consistent and reliable ultraviolet output over the entire life of the lamp to ensure continuous purification
- Built with a durable stainless steel chamber to prolong life and eliminate ultraviolet light degradation
- UV sensor to provide continuous readout of UV intensity
- The controller visually displays the remaining lamp life and will go into alarm if the lamp fails
- The controller has a sealed case to prevent damage from accidental water intrusion and is fully CSA and CE compliant
- Max operating pressure: 860kPa
-
- Specially designed and tested Sterilume™-HO lamps provide consistent and reliable ultraviolet output over the entire life of the lamp to ensure continuous purification
- Built with a durable 316L stainless steel chamber to prolong life and eliminate ultraviolet light degradation
- Specialised 254mm UV intensity sensor with output to enable solenoid valve or remote alarm (SHFM models)
- The controller visually displays the remaining lamp life and will go into alarm if the lamp fails
- Max operating pressure: 860kPa
-
- NSF55 Class A Certified (PRO10, 20, 30)
- USEPA UVDGM Validated (PRO 50)
- USEPA 2-Log Adenovirus validation (PRO24-100)
- USEPA 4-Log Adenovirus validation (PRO 24-186)
- CoolTouch Fan function to reduce water temperature
- Flow sensor monitor for real-time UV dose (PRO 10, 20, 30)
- LightWise technology allows controller to reduce lamp power during periods of no-flow to maintain water temperature below 40°C (PRO 10, 20, 30 only)
- Optional COMMcenter displays UV dose and can monitor up to 9 UV systems!
- Controller interface includes audible alarm, lamp/controller/fan/solenoid valve/sensor/flow-meter operation indicators, flow rate sensor set-point alarms
-
- High quality stainless steel piping and frame construction
- Dead zone free construction
- Tank-less heating technology, removing risk of potential endotoxin accumulation
- Remote monitoring and control functionality ensuring rapid response / support
- Demand-rated control and water recycling / recovery technology
-
- Permeate flows up to 36,000 L/day
- Grundfos high pressure pump
- 5 micron sediment pre-filter
- Float switch, feed and permeate water pressure switches
- 4040 RO membranes
- EConnect controller - online live system performance monitoring
- Options - antiscalant dosing, permeate membrane rinse, raw water blending
- Permeate conductivity and temperature sensors
- Permeate, drain and recycle water rotameters
- Process controller with status of level, pressure and stop switches; permeate conductivity and temperature readout, alarm signal
-
- Flows up to 1.5 L/s
- Compact design ensures minimum installation disruption
- Backwash cleaning process via rotating suction arms
- 100 micron stainless steel screen
- No interruption to water flow during screen cleaning
- Can be mounted in vertical or horizontal pipe runs
- Clear viewing glass enables full view of screen and backwash operation
- Operating pressure range: 200 - 1600kPa
-
- Flows up to 4.7 L/s
- Backwash cleaning process via rotating suction arms
- 100 micron stainless steel screen
- No interruption to water flow during screen cleaning
-
- Flows up to 4.7 L/s
- Automatic backwash via timer control (Adjustable settings of 24hr, weekly, monthly, and 2 monthly)
- Backwash cleaning process via rotating suction arms
- 100 micron stainless steel screen
- No interruption to water flow during screen cleaning
- Can be mounted in vertical or horizontal pipe runs
- Clear viewing glass enables full view of screen and backwash operation
- BMS connection for operation and fault status as standard
- Minimum operating pressure: 200kPa
- Pressure class: PN16
-
- Flows up to 55.5 L/s
- Extremely efficient screen cleaning ratio of 1:1 using point rotation principle
- Standard 100 micron stainless steel screen (Silver coated to inhibit bacterial growth)
- No interruption to water flow during screen cleaning
- Can be mounted in vertical or horizontal pipe runs
- Clear viewing glass enables full view of screen and backwash operation
- Minimum operating pressure: 200kPa
- Pressure class (25mm-DN65): PN16
- Pressure class (DN80-DN200): PN10
-
- Flows up to 21.6 L/s
- Automatic backwash via timer control (Adjustable settings of 4hr, 8hr, 24hr, weekly and monthly)
- Extremely efficient screen cleaning ratio of 1:1 using point rotation principle
- Standard 100 micron stainless steel screen (Silver coated to inhibit bacterial growth)
- No interruption to water flow during screen cleaning
- Can be mounted in vertical or horizontal pipe runs
- Clear viewing glass enables full view of screen and backwash operation
- BMS connection for operation, fault and backwash status available
- Minimum operating pressure: 200kPa
- Pressure class (25mm-DN65): PN16
- Pressure class (DN80-DN200): PN10
-
- Flows up to 55.5 L/s
- Automatic backwash via differential pressure and timer control
- Extremely efficient screen cleaning ratio of 1:1 using point rotation principle
- Standard 100 micron stainless steel screen (Silver coated to inhibit bacterial growth)
- No interruption to water flow during screen cleaning
- Can be mounted in vertical or horizontal pipe runs
- Clear viewing glass enables full view of screen and backwash operation
- BMS connection for operation, fault, and backwash status available
- Minimum operating pressure: 200kPa
- Pressure class (25mm-DN65): PN16
- Pressure class (DN80-DN200): PN10
-
- Flows up to 6.1 L/s
- Extremely efficient screen cleaning ratio of 1:1 using point rotation principle
- Standard 100 micron stainless steel screen (Silver coated to inhibit bacterial growth)
- No interruption to water flow during screen cleaning
- Can be mounted in vertical or horizontal pipe runs
- Clear viewing glass enables full view of screen and backwash operation
- Fitted with DN80-DN200 screen for greater surface area
- Minimum operating pressure: 200kPa
- Pressure class: PN10
-
- Flows up to 6.1 L/s
- Automatic backwash via timer control (Adjustable settings of 4hr, 8hr, 24hr, weekly and monthly)
- Extremely efficient screen cleaning ratio of 1:1 using point rotation principle
- Standard 100 micron stainless steel screen (Silver coated to inhibit bacterial growth)
- No interruption to water flow during screen cleaning
- Can be mounted in vertical or horizontal pipe runs
- Clear viewing glass enables full view of screen and backwash operation
- BMS connection for operation, fault, and backwash status available
- Fitted with DN80-DN200 screen for greater surface area
- Minimum operating pressure: 200kPa
- Pressure class: PN10
-
- Flows up to 6.1 L/s
- Automatic backwash via differential pressure and timer control
- Extremely efficient screen cleaning ratio of 1:1 using point rotation principle
- Standard 100 micron stainless steel screen (Silver coated to inhibit bacterial growth)
- No interruption to water flow during screen cleaning
- Can be mounted in vertical or horizontal pipe runs
- Clear viewing glass enables full view of screen and backwash operation
- BMS connection for operation, fault, and backwash status available
- Fitted with DN80-DN200 screen for greater surface area
- Minimum operating pressure: 200kPa
- Pressure class: PN10
-
- Reduces Chlorine, chlorine taste and odour. Decreases organic based colour, taste, odour, pesticides and chemicals.
- Media filtration using a bed of carbon, crushed glass, anthracite, crushed granite or other material.
- Fully automatic media filtration
- Used to filter water for various applications e.g. drinking, swimming pools, aquaculture, irrigation, stormwater management, oil and gas operations.
-
Single Glass AFM Media Filters: Superior sediment filtration removing up to 95% of particles down to 1 micron. As well as the efficient removal of hydrophobic hydrocarbons (oil & fats) organics and Microplastics. Duplex Glass AFM Media Filter for High Capacity Service Flow Rate: Sediment particle filtration to as low as 1 micron, removing hydrocarbons, organics and microplastics.
-
Single Sediment Removal Filter:
- High flow sediment filtration down to 5 micron with superior loading capacity.
- Suitable for dirt, rust, sand, and other fine particles.
- High flow sediment filtration down to 5 micron with superior loading capacity.
- Suitable for dirt, rust, sand, and other fine particles.
-
- Addresses hard water problems such as calcification, scaling, and spotting by removing magnesium and calcium hardness minerals and discarding them to drain.
- Single or multiple softener configurations
- 5-cycle automatic softener valves
- Water meter regeneration initiation
- Single, alternating, or twin metered controls
- Sequential or parallel controls for multiple softeners
- Free standing FRP fiberglass wrapped polyethylene resin tanks
- Heavy duty polyethylene brine tanks and lids
- Food grade high capacity softener resin
-
- 10" 10 mm - Flows up to 0.66L/s (40L/m)
- 20" 20 mm - Flows up to 1.33L/s (80L/m)
- Durable reinforced polypropylene housings, standard diameter (2.5”)
- Pressure relief / bleed valve
- Supplied with wall-mount bracket and spanner
- Watermark® Certification
- Max operating pressure: 800kPa
- Min/Max operating temperature: 4°C/45°C
- Brass BSP inlet/outlet ports
- Carbon and resin options, please contact.
-
- Flows up to 3.0 L/s
- Durable reinforced polypropylene housings, larger diameter (4.5”)
- Pressure relief/bleed valve
- Supplied with mounting screws, bracket & spanner.
- Watermark® Certification
- Max operating pressure: 830kPa
- Max operating temperature: 45°C
- Min operating temperature: 4°C
-
- Flows up to 8.7 L/s
- Swingbolt lid closure mechanism
- Side inlet, side outlet
- Includes vent valve and pressure gauge
- 316 Grade stainless steel construction
- 50mm (2”) BSPF inlet/outlet
Southland Filtration is a leading Australian provider of commercial water filtration solutions. We’ve been helping businesses since 1995 with a focus on quality, custom solutions, and reliable service. We work with businesses and organisations in Australia and New Zealand to address their unique water challenges and maintain the highest standards.